钢化玻璃玻璃免烘烤移印油墨

1、 适用材质：金属、电镀、氧化铝、电解板、铝塑板、喷（烤）漆、喷塑、PA塑料尼龙、电木、玻璃钢、密胺等。

2、 产品特性：半光、免烘烤、耐酒精、耐冲压。

3、 稀释剂：本公司B-03稀释剂或783慢干稀释剂。

4、 固化剂：本产品为单组份油墨，如有特殊要求也可选择添加固化剂增加附着力及墨层抗性。

5、 油墨调配：充份搅拌后取所需用量进行调配使用，双组份油墨先按比例添加固化剂搅拌均匀，然后再添加稀释剂稀释到合适粘度进行印刷；添加固化剂后的油墨**过使用时限会产生粘稠胶化现象，请及时清洗网版，并弃用油墨，不可回收。

6、 网版及刮胶：适合80T-140T（200目-350目）聚脂网纱，聚氨脂PU油性刮胶。

7、 干燥条件及时间：本产品可以常温干燥，也可以烘烤快速干燥，建议干燥温度及时间为25℃/24小时，60℃/40分钟，80℃/30分钟，100℃/20分钟。

8、 性能检测：
用3M600胶带划百格测试**无脱落；
用棉布沾95%工业酒精以500G力水平来回擦拭100次无脱色；
1mm厚铝片在印刷位置进行冲断、卷边、延压后边缘位置**无脱落；

9、 包装规格：1KG/胶罐，12罐/箱。

10、储存条件：置于干燥通风处常温保存；避免高温、太阳直射，严禁烟火。

11、注意事项：请向我司索取《MSDS安全使用手册》，并按指引进行安全生产。 
1, applicable materials: metal, electroplating, alumina, electrolytic plate, aluminum plate, spray paint, spray (baked), PA nylon, bakelite plastic, glass steel, melamine etc..

2, product characteristics: half light, no baking, alcohol resistance, stamping.

3. Diluent: the company's B-03 diluent or 783 slow dry diluent.

4, curing agent: This product - ink, if there are special requirements can also choose to add curing agent to increase adhesion and ink layer resistance.

5, ink deployment: fully mixing after the dosage required for the deployment, two-component ink first adding curing agent according to the proportion of mixing evenly, then add the diluent to the appropriate viscosity of printing ink; curing agent is added after more than the use of time will produce viscous gel phenomenon, please clean the screen, and abandoned ink Unrecyclable.

6, screen and frictioning: for 80T-140T (200 -350 mesh) polyester mesh, polyurethane PU oily frictioning.

7, drying conditions and time: This product can be dried at room temperature or dry quickly. It is recommended that the drying temperature and time should be 25 /24, 60 /40, 80 /30, 100 /20.

8. Performance testing:
Use 3M600 tape to make 100 lattice tests ** without falling off.
With cotton cloth, 95% industrial alcohol was wiped back and forth at the level of 500G force for 100 times without decolorization.
The position of 1mm thick aluminum sheet in the printing position is broken, curling, and the edge position after the pressure is ** without falling off.

9, packaging specifications: 1KG/ glue cans, 12 cans / boxes.

10. Storage conditions: keep at room temperature in the dry and ventilated place; avoid high temperature, direct sunlight, and strictly prohibit fireworks.

11, attention: please ask our department "MSDS safety manual" and carry out safety production according to the guidelines.