耐酸碱抗腐蚀电镀保护油墨

本产品采用高级进口丙烯酸树脂和高级颜料经过细制研磨加工组合而成，适用于各种金属、玻璃、陶瓷、石材、电镀(含水电镀)、阳极氧化铝表面、静电喷漆面及烤漆面等制品的丝印及移印，不需加固化剂，不需烘烤，即可获得优异的附着力。油墨特性： 1、 平光（如需亮光请选择我司JL系列）、附着力佳、耐酒精、耐化学品； 2、 手感好，流平性佳、面光洁； 3、 表面硬度好，耐冲击性能强、抗刮伤； 4、 耐酒精、耐化学品程度佳；印刷：选用网目为100-420目，以120T聚酯单丝、感光胶网版计算涂覆盖面积每公斤达35~40㎡。表干时间自然挥发5-10分钟，实干时间在24小时以内，48小时后达较佳性能。 1．用B-03**稀释剂** 2．用718洗网水洗网。 3．可选择添加JS-9硬化剂10%用于增加油墨附着力及物理化学抗性。 4．烤箱80℃烘烤30分钟佳能更优。测试方法（完全干燥后）： 1．3M胶纸粘在画有百格的油墨表面45度角迅速拉起不脱油。 2．纯度99%的酒精500G力在油墨表面来回擦拭200次无脱色。使用方法： 1．使用前应充分搅拌，用后随时密封。 2．搅拌时先加固化剂静置10分钟后，再加稀释剂10-15%，稀释到印刷粘度。 3. 加入固化剂的油墨使用时限为4-6小时，过期请弃用，剩余油墨不可回收。 4．网版塞网时可用洗网水清洗。 5．不得与其它类型油墨混合使用。注意事项： 1．各种物料的外观相似，但可能会是不同的材料，客户需先试印，确其符合要求后，再批量生产。 2．在移印过程中，如出现拉丝或散开现象，可适当加入一些慢干膏即可。 3．环境温度过高，将会影
响油墨原有质量。 4．请远离火源，避光保存。This product adopts advanced import acrylic resin and senior pigment after fine grinding system combination, applicable to all kinds of metal, glass, ceramic, stone, plating (water plating), and silk screen printing electrostatic anodic alumina surface, spray paint surface and paint surface and other products, without curing agent, and does not need to bake, can to obtain excellent adhesion. Ink characteristics: 1, Matt (for light please choose our JL Series), good adhesion, resistance to alcohol, resistant to chemicals; 2, feel good, good leveling, surface smooth; 3, surface hardness, strong impact resistance and scratch resistance; 4, alcohol resistant, chemical resistant degree preferred; printing: choose for 100-420 mesh mesh with 120T polyester monofilament, photosensitive adhesive coated screen calculation area per kilogram of 35~40 square meters. The drying time naturally volatilized for 5-10 minutes, the actual drying time was within 24 hours, and the best performance was reached after 48 hours. 1. use B-03 special diluent * * * * 2. to wash net with 718 net. 3. the JS-9 hardened agent 10% can be added to increase the adhesion and physical and chemical resistance of the ink. 4. oven 80 C baking 30 minutes better Canon. Test method (after complete drying): 1.3M adhesive paper sticky to the printing ink surface of the painting with a 45 degree angle quickly pull off the oil. 2. purity of 99% alcohol 500G force is wiped back and forth on the surface of the ink for 200 times without decolorization. Method of use: 1. should be fully stirred before use and seal at any time after use. After 2. agitation, add the curing agent for 10 minutes, then add the diluent 10-15%, and dilute it to the printing viscosity. 3. the use time limit of the ink for curing agent is 4-6 hours, expired and the remaining ink can not be reclaimed. 4. net plate net can be washed by washing water. 5. not to be used in combination with other types of ink. Note: 1. the appearance of various materials is similar, but may be different materials, customers need to test the first print, it is in line with the requirements, and then batch production. 2. in the process of printing, if the phenomenon of drawing or dispersing, some slow dry paste can be properly added. 3. the temperature of the environment is too high.
Sound the original quality of the ink. 4. please keep away from the fire source and avoid the light.