玻璃自干丝印油墨 玻璃油墨 丝印油墨 自干油墨

玻璃自干丝印油墨

品牌：欧莱斯
适用对象：金属，玻璃，陶瓷，电镀，五金，不锈钢，铝合金，拉丝面板
单件净重：1公斤
着色力：100
细度：0.01
粘度：1500S
流动度≥：100
保质期：72个月
型号：MPL
用途：1.适用范围:铁、铝、合金、玻璃、陶瓷、电镀、石材、阳极氧化铝表面及烤 （喷）漆面等2.稀释剂:用本公司S-03稀释剂3.固化剂:可添加TA-9154硬化剂10%增加附着力,提高墨膜硬度。
耐温性：低温玻璃油墨
性能：自干玻璃漆
供应玻璃油墨基本信息
本产品是采用高级进口丙烯酸树脂和高级颜料经过细制研磨加工组合而成，用于各种金属、玻璃、陶瓷、石材、电镀(含水电镀)、阳极氧化铝表面及烤（喷）漆面等制品的丝印及移印，不需加固化剂，不需烘烤，即可获得优异的附着力。
油墨特性：
1、平光、附着力佳、耐汽油、耐化学品；
2、手感好，流平性佳、面光洁；
3、表面硬度好，耐冲击性能强、抗刮伤；
4、耐汽油、耐酒精、耐化学品程度佳；
印刷：
选用网目为100-350目，以120T网纱计算涂覆盖面积每公斤达30~35㎡。
表干时间自然挥发5-15分钟，实干时间在24小时以内，48小时后达较佳性能。
1．用配套**稀释剂开油水
2．用718洗网水洗网。
3．或添加配套硬化剂10%可增加附着力,提高墨膜硬度。
4．烤箱80℃烘烤10分钟佳能更优。
测试方法（完全干燥后）：
1．3M胶纸粘在画有百格的油墨表面45度角迅速拉起不脱油。
使用方法：
1．建议用我公司**稀释剂进行稀释，不建议使用783慢干稀释剂稀释，使用前应充分搅拌，用后随时密封。
2．搅拌时加本公司配套开油水10-12%，稀释到印刷适合粘度，移印稀释使用移印**稀释剂；用718洗网水清洗。
3．不得与其它类型油墨混合使用，否则容易出现其他附着力，化学反应等不良现象。
4. 加入固化剂的油墨使用时限为8小时，过期请弃用，剩余油墨不可回收
注意事项：
1．各种承印物料的外观相似，但可能会是不同的材料，客户需先试印，确其符合要求后，再批量生产。
2．在移印过程中，如出现拉丝或散开，可适当加入一些慢干膏即可;
3．环境温度过高，将会影响油墨原有质量。白色追赶150都会变色，烘烤时请用木质材料垫底进行烘烤，不得直接接触铁
4．根据气候变化，请远离火源，阴暗处15度-30度环境下存放。Glass self drying ink printing ink

Brand: oleser
Applicable objects: metal, glass, ceramics, electroplating, hardware, stainless steel, aluminum alloy, wire drawing panel
Single piece net weight: 1 kilos
Coloring force: 100
Fineness: 0.01
Viscosity: 1500S
Flow degree is larger than 100
Shelf life: 72 months
Model: MPL
Uses: 1.: application: iron, aluminum, alloy, glass, ceramics, electroplating, stone, anodized aluminum surface and baking (spray) paint and other 2. diluents: use our company S-03 diluent 3. curing agent: add TA-9154 hardening agent 10%, increase adhesion, improve ink film hardness.
Temperature resistance: low temperature glass ink
Performance: self drying glass lacquer
Basic information on supply of glass ink
This product is the use of advanced import acrylic resin and senior pigment after fine grinding system combination, all kinds of metal, glass, ceramic, stone, used for electroplating (aqueous electroplating), anodic alumina surface and baked (spray) and silk screen printing products such as paint, without curing agent, and does not need to bake, can be obtained excellent adhesion.
Ink characteristics:
1, Matt, adhesion, petrol, chemical resistance;
2, good feel, good leveling, smooth surface;
3, the surface hardness is good, the impact resistance is strong, and the scratch resistance is good.
4. Good resistance to gasoline, alcohol and chemicals.
Printing:
Choose for 100-350 mesh mesh, 120T mesh with coverage area calculation per kilogram of 30~35 square meters.
The drying time naturally volatilized for 5-15 minutes, the actual drying time was within 24 hours, and the best performance was reached after 48 hours.
1. use special diluent to open oil and water
2. wash net with 718 net.
3. or adding the supporting hardening agent 10% can increase the adhesion and improve the hardness of the ink film.
4. oven 80 C baking 10 minutes better Canon.
Test method (after complete drying):
1.3M adhesive paper sticks to the surface of the printing ink at 45 degrees and quickly pull up and not remove oil.
Usage method：
1. it is suggested that we use our company's special diluent to dilute it and not recommend the use of 783 slow dry diluents. It should be fully stirred before use and sealed at any time after use.
2. add the company supporting stirring open water 10-12%, diluted to printing for viscosity, printing the dilution used printing special thinner; use clean water to wash the nets 718.
3. not to be used with other types of ink, otherwise other adhesion, chemical reaction and other bad phenomena.
4. the use time limit of the ink for curing agent is 8 hours, expired and the remaining ink can not be recycled
Matters needing attention：
1. the appearance of all kinds of printed materials is similar, but it may be different materials. The customer needs to test the printing before it meets the requirements and then is produced in batch.
2. in the process of transfer printing, such as drawing or dispersing, can appropriately add some slow dry paste;
3. the high temperature of the environment will affect the original quality of the ink. White beyond 150 will change color, when baking, please use wood material at the bottom to bake, no direct contact with iron
4. according to the climate change, please keep away from the fire source and store the shade at 15 degrees -30 degrees.