阳极氧化铝材移印油墨

阳极氧化铝移印油墨

本产品采用高级进口丙烯酸树脂和高级颜料经过细制研磨加工组合而成，适用阳极氧化铝、阳极氧化铁、阳极氧化金属、铝材氧化、金属氧化、阳极氧化铝表面、阳极氧化保护等制品的丝印及移印，不需加固化剂，不需烘烤，即可获得优异的附着力。油墨特性：1、平光(如需亮光请选择我司JL系列)、附着力佳、耐酒精、耐化学品；2、手感好，流平性佳、面光洁；3、表面硬度好，耐冲击性能强、抗刮伤；4、耐酒精、耐化学品程度佳；印刷：选用网目为100-420目，以120T聚酯单丝、感光胶网版计算涂覆盖面积每公斤达35~40㎡。表干时间自然挥发5-10分钟，实干时间在24小时以内，48小时后达较佳性能。1.用B-03**稀释剂开油水2.用718洗网水洗网。3.可选择添加JS-9硬化剂10%用于增加油墨附着力及物理化学抗性。4.烤箱80℃烘烤30分钟佳能更优。测试方法(完全干燥后)：1.3M胶纸粘在画有百格的油墨表面45度角迅速拉起不脱油。2.纯度99%的酒精500G力在油墨表面来回擦拭200次无脱色。使用方法：1.使用前应充分搅拌，用后随时密封。2.搅拌时先加固化剂静置10分钟后，再加稀释剂10-15%，稀释到印刷粘度。3. 加入固化剂的油墨使用时限为4-6小时，过期请弃用，剩余油墨不可回收。4.网版塞网时可用洗网水清洗。5.不得与其它类型油墨混合使用。注意事项：1.各种物料的外观相似，但可能会是不同的材料，客户需先试印，确其符合要求后，再批量生产。2.在移印过程中，如出现拉丝或散开现象，可适当加入一些慢干膏即可。3.环境温度过高，将会影响油墨原有质量。4.请远离火源，避光保存。Anodic aluminum oxide printing ink
This product adopts advanced import acrylic resin and senior pigment after fine grinding system c o mbination and, applicable anodic alumina, anodic oxide, anode oxidation metal, aluminum oxide, metal oxidation, anodic alumina surface, anodic oxidation protection products and silk screen printing, without curing agent, and does not need to bake, can obtain excellent adhesion. Ink characteristics: 1, Plano (for light please choose our JL Series), good adhesion, alcohol resistant, resistant to chemicals; 2, good hand feeling, good leveling, smooth surface; 3, good surface hardness, strong shock resistance, anti scratch; 4, alcohol resistant, chemical resistant degree is good; printing: choice of mesh for 100-420 orders, in 120t polyester monofilament, photosensitive adhesive screen calculation coated area coverage per kilogram of 35-40 square meters. Table dry time natural volatile 5-10 minutes, hard work time within 24 hours, 48 hours after the best performance. 1 using B-03 special thinner to open the oil and water 718 with 2 wash water n e t w ork. 3 can choose to add JS-9 10% hardening agent for increasing ink adhesion and physical and chemical resistance. 4 oven 30 for 80 minutes, Canon is better. Test method (c o mpletely dry):1.3M gummed paper tape‘s ink surface 45 degree angle quickly pulled off the oil painting. 2 purity 99% alcohol 500G force on the surface of the ink to wipe 200 times without decolorization. Usage: 1 before use should be fully stirred, with the use of sealed. 2 stirring, the first 10 minutes after the curing agent, then add 10-15%, diluted to printing viscosity. 3 add hardener inks use time is 4-6 hours, please not expired, the remaining ink unrecyclable. 4 screen plug mesh used when washing n e t w ork water cleaning. 5 may not be mixed with other types of ink. Note: 1. All kinds of material similar in appearance, but may be different materials, customers need to try printing and ensure its requirements, and then bulk production. 2 in the printing process, such as drawing or spread phenomenon, may be appropriate to add some slow dry paste. 3 environmental temperature is too high, will affect the quality of ink. 4 please keep away from fire and light.