耐酸碱自干氧化铝油墨

 1、适用范围:本产品主要用于各种金属、陶瓷、石材、电镀、阳极氧化铝表面、静电喷漆面及烤漆面等制品的丝印及移印;不需加固化剂,不需烘烤,即可获得优异的附着力。
2、产品特性:亮光、附着力佳、耐酸碱、耐酒精、耐冲压。
3、稀释剂:用B-03**稀释剂或783开油,用718洗网水清洗网版。
4、固化剂:可选择添加JS-10**固化剂用于增加油墨附着力及物理化学抗性
5、油墨调**法:开罐先搅拌均匀,取所需量油墨稀释到合适印刷粘度。如需添加固化剂,先加固化剂搅拌后静置10分钟,待油墨与固化剂完全交联后再进行稀释。
6、干燥时间:常温干燥,表干时间5-10分钟,实干时间在24小时以内,48小时后达较佳性能,烤箱80℃烘烤30分钟性能更优。
7、添加固化剂后的使用时限:4-6小时,过期请弃用,剩余油墨不可回收。
【性能检测】
1、3M胶带划百格测试:**无脱落
2、耐冲压测试:1mm厚铝板180°折弯无变化。
3、耐酒精测试:用脱脂棉沾浓度99%工业酒精以500G力水平来回200次无脱色。
【注意事项】
1、先小量试印确认符合要求后再批量生产。
2、做好承印物的表面清除油脂及杂质工作,以促进附着效果。
3、附着力、硬度、耐酸性、耐酒精性、耐化学品性、抗划伤性、耐磨性等性能的检测,需要完全固化后方可检测。
4、未经允许情况下,不得将本系列油墨与其它类型油墨混用及配色。
5、油墨,稀释剂使用及储存时严禁烟火。
6、使用时注意施工场所的通风状况良好,尽量避免**直接接触。
7、本品不慎溅入口、鼻、眼、耳内,应用大量水清洗或直接求助医生。1, scope of application: This product is mainly used for screen printing and pad printing of all kinds of metal, ceramics, stone, electroplating, anodized alumina surface, electrostatic painting surface and baking paint surface. It can get excellent adhesion without curing agent and baking.
2, product characteristics: gloss, adhesion, acid and alkali resistance, alcohol resistance, stamping.
3, diluent: use B-03 special diluent or 783 to open oil, and use 718 net water to clean the net plate.
4, curing agent: a special JS-10 curing agent can be added to increase the adhesion and physical and chemical resistance of ink
5, ink transfer method: the tank first stirred evenly, and the required ink was diluted to the appropriate printing viscosity. If the curing agent is added, the solidifying agent is stirred for 10 minutes after mixing, and then the ink is completely crosslinked with the curing agent and then diluted.
6, drying time: dry at room temperature, dry time for 5-10 minutes, dry time within 24 hours, 48 hours after the best performance, oven 80 degrees baking 30 minutes, better performance.
7, the use time limit after adding curing agent: 4-6 hours, expired please discarded, the remaining ink can not be recycled.
[performance detection]
1, 3M tape test: ** no shedding
2, resistance to stamping test: 1mm thick aluminum plate 180 degree bending no change.
3. Alcohol tolerance test: 99% industrial alcohol was stained with skimmed cotton at 500G force level for 200 times without decolorization.
[cautions]
1, the first small test print confirms that it meets the requirements and then batch production.
2, do a good job of removing oil and impurities on the surface of the material to promote the effect of attachment.
3, adhesion, hardness, acid resistance, alcohol resistance, chemical resistance, scratch resistance, wear resistance and other properties, need to be completely cured after testing.
4. In the absence of permission, this series of ink can not be mixed with other types of ink and color matching.
5. Ink, the use and storage of diluents strictly prohibit fireworks.
6. In use, pay attention to the ventilation of the construction site and avoid direct contact as far as possible.
7, this product is inadvertently splashed in the entrance, nose, eye and ear, and uses a lot of water to clean or direct to the doctor.